I purchased a switch while late (switch repair notation 1)

huaweiwearabless 01/02/2023 557

I purchased a switch while late (switch repair notation 2)

I purchased a switch while late (switch repair notation 3)

As the title suggests, I bought a switch.It is used in 2017.

I think there are some ways to think, "It's a mess, but I chose 2017 and bought it.

The reason was that I wanted a non -countermeasure.

I don't know what to use for without explaining what to use.

This used switch was available for about 20,000 yen including shipping with Mercari.

The state was relatively good, and it was an individual who could understand that he used it very carefully.

As an explanation in advance,

It was said that there was a common problem.

These two are famous because of their quite high incidence.

In Youtube, the contractor has too many problems with the incidence and cannot respond, so retail repair parts and explain the method as "Please fix it yourself."

With a PC self -made ER, it is a task that can be done without difficulty, so I purchased parts from Asuka Repair Road, a leading domestic person in switch repair, and repaired these two problems on my own.

By the way, I purchased it almost at the same time as the main unit, but the repair parts arrived faster.

First, confirm the condition

The arrived switch body was quite good, and there was no problem in which the joycon on the left moved on its own.

However, it occurred as I used it, so the condition was "gradually getting worse."

There was a problem that the joycon on the left would come off without pressing the lock button.

The photo is removed, but all the inner bags of the vinyl remain, and they are quite good.

I think that the occurrence of a problem is almost aging.

What has occurred this time is the above two symptoms.Joy Conrock defect and joy concise failure.

I will post some photos during the work, but it is not unknown for the video, so if you are determined to be repaired on your own, it is recommended that you watch the above videos.

Repair part 1 Metal lock buckle

Repair Parts 2 Joycon Analog Stick

Tool set used this time

Magnet sheet attached to the tool set.Steel screws are stuck and hard to lose.Ideas

Leave the left joycon.

Replace analog sticks

The so -called "3 pieces"

It is a replaced buckle.It was confirmed that the locking part on the upper left of the resin was shaved.

Joycon replaced with metal parts and assembled.You can see that the next door of the black button is metal and shines.Please compare it with your joycon.

The right joycon was broken.From here, remove the table with the battery and lower it to three.

The right work is similar, so I will omit it.

After replacement, adjust the joystick with the main unit settings.

Is it easy?

What is different from your own PC

This is about it.

If you are on your own PC, the difficulty is not so high if you know the procedure.

If you have the opportunity, please try it.

Here are the tools used this time.

A tool set that can replace 122 types of attachments including special screws.If you repair a mobile device, you definitely want to have it

【限定】E·Durable 122in1 精密ドライバーセット 磁気ドライバー 特殊 ドライバー 多機能ツールキット ネジ回し iPhone Switch 家電 デジタル製品 修理キット 101種ビット【117昇級】created by RinkerE·Durable

This time it was only joycon, but the trick point screw was the 15th in the Y -shaped, and the small " + screw" inside was perfect.

Don't lick the screws using different sizes.The resin on the joycon side is quite soft, so the screws are easy to turn, so I think there is almost no problem.

100 yen shop -precision driver set

The set of precision drivers sold at the 100 yen shop, such precision drivers have a fixed torque and do not have any overdoing power, so it is suitable for trying whether the screw is likely to turn.After removing the screws, it can be used to open the attached parts.

However, please do not break it too much.

100 yen shop -assembled driver set

This time, I used the flathead screwdriver to remove the parts.It is easy to use because it is just the right size and rigidity.

Repair part

Asuka repair hall official HP -Nintendo Swich related repair parts sales

Asuka repair hall official HP -Nintendo Switch Parts -Metal Lock

Asuka repair hall official HP -Nintendo Switch Parts -Switch Joycon Repair Analog Stick Base Plate (Idi)

* You pointed out in the comments.It seems that Amazon sells under the name of "Asuka repair hall" is a fake.confusing···.I think it would be better to offer Amazon ... (bitter smile

This time, only the left (blue) had a problem, but the right side (orange) was also replaced mechanically.

The individual this time is the initial type, so four years after its release, the operation parts are about to break down due to aging, so we took this opportunity to replace the joystick and rock buckle parts on this occasion.

The bug has been cleaned up neatly and it has become more comfortable.

The price of the switch was soaring due to the malicious purchase of the reseller, but the market price has fallen overall due to the release of the organic EL model.

The market price of the inexplaced junk, which had risen due to soaring prices, was also significantly increased, but I think it will probably fall due to a decline in the main unit price.

If you fix it, it will sell at a high price, so it is worth it, but it is not worth it.

Reasons why malfunctions are concentrated on the joycon on the left

This time, only the joycon on the left had a problem.

According to the video of Asuka Repair, about 8-9 % of the individuals brought to joycon repair are concentrated on the left.

遅ればせながらスイッチを購入しました(スイッチ修理記1)

Why is bugs concentrated on the left, even though they have the same structure on both the left and right?I was wondering, but this time I took the switch in my hand and pinned it.

The cause is "Battery".

There is a large battery on the left side of the switch, which is quite heavy.

In short, since the center of gravity is on the left, the controller at the very end is great for the "Toto principle", and the buckle lock and joycon are also overwhelmed.

Some people get hot when playing games, so there are quite a few possibility that they are unconsciously applying for unknowing power.

The controller is just a resin and low rigidity, so it means that Moro is affected by the weight of the battery.

Nobody pointed out in the video, but I think this is the "correct answer".

By the way, when you have a switch, be sure to hold it with both hands, or wear it with one hand.

The controller is overwhelmed, making it easier to break down.

The switch controller is completely insufficient, and if you try it with one hand with a trial on the main unit, you can see that the controller is slightly hazy.

I think it is necessary to make a housing with a metal frame or a harder resin.

It's a structural defect.

These structural defects do not seem to have changed even if they become organic.

Disability occurrence ...

Actually, there was no problem in particular, but I wanted to remove the cover of the main body and repaint the grease.

After four years, the grease, which had been painted first, is about to dry.

However, the four triat screws on the main unit are hard and do not come off.

I have a special skill (?) That the screw that I felt "absolutely" is 100%slick, so I would like to stop working temporarily and find some means.

I don't overdo it because the incidence is 100%.(Slimy smile

Generally, the screws are sloppy

These two points, but this time seems to be the latter.

I'm thinking about what to do.

I think you can probably avoid it if you have technology, but in my case it will probably be 100%.

If there is any movement, we will update this article and let us know.

So, this time, "I bought a switch while late" is over.

It is still undecided whether to be part2 or update this article.

The switch can now be bought at a fixed price.It is an old type.

Nintendo Switch 本体 (ニンテンドースイッチ) Joy-Con(L) ネオンブルー/(R) ネオンレッドcreated by Rinker任天堂 ¥32,970 (2022/03/24 10:36:13時点 Amazon調べ-詳細)Nintendo Switch 本体 (ニンテンドースイッチ) Joy-Con(L)/(R) グレーcreated by Rinker任天堂 ¥32,970 (2022/03/24 10:36:13時点 Amazon調べ-詳細)

at the end···

"Asuka repair hall" has published a disassembly video for the new form of OLED, so I pointed out in the tweet, but I will write what I want.

What I felt when I saw the decomposition.

The number of screws for accessing inside is reduced, making it easier to decompose.

The battery capacity has not changed from the initial model.

The SOC seems to be improved to low fever because the Sirocco fan that cools the heat sink is smaller.

The USB-C, which was the most broken factor in the old model, has an aluminum cover on the connector, but it is unknown whether the strength is increasing.

I'm not sure if it's a shield purpose or a reinforcement purpose.

I personally disappointed that the USB-C structure had not changed much.

The parts cost is cheap, but there is a reflow to remove it, so I wanted it to be easier to remove.

I think it's too far away to use a reflow machine or to raise it to 300 degrees with a heatgun after putting it with a hot plate.

But there are people who do it.(Slimy smile

In the recent repair video world, after applying flux and reflecting, after sucking the solder with a solder sucking line, the BGA chip is revoled and attached again.

It looks easy to do, but be careful as you can't usually manage it.

Also, even if you fix it, it may be that the implementation parts of the board are exposed to high temperatures due to fatal damage and the life will be extremely shortened.

There will be a lot of courage to repair for a fee.

Return the story.

The OLED display unit is integrated with the touch panel (digitizer) unlike the old model.

In addition, the digitizer is glass and it breaks when it is dropped.

Since it is integrated with the display, it will be replaced with all units when divided.

It seems that the body frame on the back of the organic EL has become aluminum instead of resin, so the overall strength has increased.

The old model had an individual that was warped with heat, but I think it will decrease in the future.

Under these circumstances, if you buy a small child, I think that an old switch is better instead of an organic EL.

The old model does not use glass, so it will not break even if it is dropped, so it is safe.

Of course, if you drop it, it may break, but at least the cracked glass fragments do not injure your child.

OLED models are relatively unusual, but it is a disappointing finish overall, including the fact that the performance did not increase.

I wonder if Joycon, which has been criticized, did not review the drastic structure.

OLED EL is only resold, so I will not put it, but I will leave only the search link.

Search Amazon with "Nintendo Switch OLED OLE Model"

The "Nintendo Switch OLED Model" released on October 8, 2021 is a resold product that sells at a higher price of 37,980 yen [tax included].

Even if it claims to be a new article unopened, it is a used item, it is the same as a personal trading, and you will not receive free repair support within the warranty period.

The switch is a product that has some structural problems, as you have explained so far, so be sure to avoid purchasing from a reseller.

From Nintendo Official, repair service regulations

Even during the warranty period, the following cases will be repaired.

(Omitted)

(12) When the product purchased is transferred (used goods) regardless of whether it is free after use.

続き・・・I purchased a switch while late (switch repair notation 2)

I purchased a switch while late (switch repair notation 3)